NEW FROM hgwmodels Markings

f109 G-6/G-14 Reichsverteidigung – PLUS – 1/48 – 248066

Reference: 248066

Condition: New product

The set contains

1x Bf109 G-6/G-14 Reichsverteidigung – Markings 1/48 – 248060

2x Bf109 G-K – Stencils 1/48 – 248030

The biggest issue relating to using ordinary decals is the varnish which creates a glossy film around the decal. It is quite hard to work with classic decals the way to make this film invisible and it is impossible to reach a good result in case of metallic surfaces. OK, there are dry transfers on the market but work with them is also quite uncomfortable, it is hard to place them correctly and a modeler has the one chance only.

HGW's wet transfers are similar to ordinary decals. It is possible to move them during the attaching process and find the best position. Then just push the water from below the transfer, let it dry few hours, remove the transfer foil and work is done. Only text or symbol stays attached to the surface.

Instructions:

1. Cut the required part.
2. Soak in hot water and wait till the decal loose its base-paper.
3. Apply as regular decal.
4. Push the water from below the decal.
5. Let it dry for 2-3 hours.
6. Remove the transfer foil and clean the glue stains with water.


Focke Wulf Fw190A8/R2 Reichsverteidigung – PLUS – 1/48 – 2480658 – 248065

Reference: 248065

Condition: New product

The set contains

3x Focke-Wulf Fw 190A – Stencils 1/48 – 248042

1x Focke Wulf A8/R2 Reichsverteidigung – Markings 1/48 – 248059

The biggest issue relating to using ordinary decals is the varnish which creates a glossy film around the decal. It is quite hard to work with classic decals the way to make this film invisible and it is impossible to reach a good result in case of metallic surfaces. OK, there are dry transfers on the market but work with them is also quite uncomfortable, it is hard to place them correctly and a modeler has the one chance only.

HGW's wet transfers are similar to ordinary decals. It is possible to move them during the attaching process and find the best position. Then just push the water from below the transfer, let it dry few hours, remove the transfer foil and work is done. Only text or symbol stays attached to the surface.

Instructions:

1. Cut the required part.
2. Soak in hot water and wait till the decal loose its base-paper.
3. Apply as regular decal.
4. Push the water from below the decal.
5. Let it dry for 2-3 hours.
6. Remove the transfer foil and clean the glue stains with water.


Bf109 "Afrika" – PLUS – 1/48 – 248064

Reference: 248064

Condition: New product

The set contains

1x Messerschmitt Bf109 "Afrika" – Markings 1/48 – 248050

2x Messerschmitt Bf 109F – Stencils 1/48 – 248045

2x Bf109 G-K – Stencils 1/48 – 248030

The preparation of the surface prior to the application of the HGW Wet Transfer:

  • The HGW Wet Transfer technology has been tested on Gunze brand paints and preparations.
  • Carry out the test (not on the model), if you are applying to paint made by a different manufacturer.
  • We recommend to spray the surface with a glossy varnish in order to achieve a perfect result.
  • No matter whether you are applying the transfer onto paint or varnish, it is advisable to go over the surface using sandpaper of a grade from 6 000 to 8 000.
  • Naturally, it is also essential to ensure that the base is clean, grease-free and clear of dust.

You will need:

  • a scalpel,
  • sharp tweezers,
  • the Mr. Mark Softer product by Gunze,
  • a cotton bud and clean cloth.

Step by Step:

1. Cut out the required design using a sharp scalpel.

wet-transfers

2. Soak the base paper in warm water (approx. 20 sec).

wet-transfers

3. Remove the transfer from the base paper.

wet-transfers

4. Apply a layer of Mr. Mark Softer on the surface where you intend to apply the transfer.

wet-transfers

5. Place the transfer in the required position on the layer of Mr. Mark Softer.

wet-transfers

6. Carefully press out any excess liquid and bubbles. (Use the cloth and the cotton bud.)

wet-transfers

7. Ideally, leave it to dry for 6-8 hours.

wet-transfers

8. Carefully remove the transparent transfer film.

wet-transfers

9. Clean off any traces of transfer glue with a wet cloth.

wet-transfers
*************************************************************************************

Bf109 F/G – Stencils 1/32 – 232031

Reference: 232031

Condition: New product

להשאיר תגובה

היכנס באמצעות אחת השיטות האלה כדי לפרסם את התגובה שלך:

הלוגו של WordPress.com

אתה מגיב באמצעות חשבון WordPress.com שלך. לצאת מהמערכת /  לשנות )

תמונת גוגל פלוס

אתה מגיב באמצעות חשבון Google+ שלך. לצאת מהמערכת /  לשנות )

תמונת Twitter

אתה מגיב באמצעות חשבון Twitter שלך. לצאת מהמערכת /  לשנות )

תמונת Facebook

אתה מגיב באמצעות חשבון Facebook שלך. לצאת מהמערכת /  לשנות )

מתחבר ל-%s